• About
  • |
  • Contact
  •   English
Welcome to CNC Copper busbar machine
  English
Busbar machine sold worldwideCNC Copper Busbar Bending Punching Cutting Machine Manufacturer
Whatsapp / Tel:+8613853146766

How to use a busbar bender in LV/MV switchboard production

time: 2026-11-10 admin: Sincerity

Quick answer: in LV/MV switchboard production, the bender is used after cutting and punching, with the drawing in view, the correct radius die and a material-specific springback table. The operator positions the bar, selects HMI mode (automatic or manual) and releases a first article that is measured before the batch is launched. On the LT 303U-3-C, 503U-3-C and 803U-3-C 3-in-1 machines, that station shares the frame with cut and punch.

Estación de plegado lista para un ciclo de producción en un taller de tableros.

Bending station ready for a production cycle in a switchboard shop.

Workshop working sequence

  1. Read the drawing: material, temper, radius, angle, leg length and whether the bend is flat or edge.
  2. Select the die (R3, R5, R10, R80 or R50, or a U-die) and check that it is not worn.
  3. Load or confirm the copper or aluminum springback table; do not mix programs.
  4. On the HMI, use automatic mode (length, thickness, angle) or set stroke limits in manual mode.
  5. Make a first article, measure angle, radius and dimensions, and only then launch the run.
  6. Inspect burrs or die marks that could block assembly of an IRAM/IEC switchboard.

Flujo de producción: plano, modelo, matrices, corte, punzonado, plegado, inspección y kit.

Production flow: drawing, model, dies, cut, punch, bend, inspect and kit.

Practices that avoid rework on LV/MV switchboards

  • Do not paste a copper program onto aluminum without a trial.
  • Have engineering review bends with spacing under about 40 mm.
  • Respect the vertical-bend envelope: 10×100 mm on 303 and 12×120 mm on 503 and 803.
  • In a Buenos Aires, Córdoba or Rosario shop, kit bars by switchboard so dimensions from different drawings are not mixed.

Apoyo de recetas y de posicionamiento durante la serie de plegado.

Recipe and positioning support during a bending run.

Clases 303U-3-C, 503U-3-C y 803U-3-C: confirmen que el lote cabe en la envolvente del modelo.

303U-3-C, 503U-3-C and 803U-3-C classes: confirm the batch fits the model envelope.

Run control and FAT

For FAT or a production run, measure first, middle and last parts with the same instrument. Published angle tolerance is ±1° / ±0.5°, to be verified on the offer. A single showpiece does not represent the batch that is assembled in the switchboard.

Juego de matrices y accesorios usado en producción (radios, punzones, corte).

Die and accessory set used in production (radii, punches, cut).

Frequently asked questions

In what order is work done on a 3-in-1?

The usual order is cut, punch and then bend, so that a misplaced bend does not shift holes already made. Confirm the order on the shop drawing.

When is HMI manual mode used?

On unconventional bends or when stroke limits are set. Automatic mode covers the usual length, thickness and angle combination.

What is measured on each bar in the run?

At least the released angle and leg dimensions and, on a sample, the radius and surface. The shop sets the frequency; FAT should write it down.

How to request a quotation

For a quotation, send drawings, material (copper or aluminum and temper), maximum width × thickness, the hole and bend list, tolerances and supply voltage to [email protected] or WhatsApp +86 13853146766. More information: https://www.busductmachine.com/.

Since 2005, LJ CNC has been a proud representative of the world's premier manufacturers of copper punching and cutting machines, busbar benders, and copper bus bar bending machine.

QUICK LINKS

PRODUCT CATEGORY

CONTACT US

No.9566 Jingshi Rd.Jinan City,Shandong,China
  [email protected]
 +8613853146766
WhatsApp

WhatsApp

WeChat

WeChat

Copryright  2025 CNC Copper busbar machine All rights reserved.